Iei-integration WAFER-LX v1.22 Uživatelský manuál

WAFER-LX Motherboard Page i MODEL: WAFER-LX3.5" Low Power AMD Geode-LX 800 MotherboardCRT, LCD/LVDS, Dual LAN and SATA Rev. 1.22 – 24 February

WAFER-LX Motherboard Page x F COMPATIBILITY... 194

WAFER-LX Motherboard Page 82 Î IDE Master and IDE Slave When entering setup, BIOS auto detects the presence of IDE devices. The Standard CMOS Featu

WAFER-LX Motherboard Page 83 Î Total Memory The Total Memory is NOT user configurable. 6.2.1 IDE Primary Master/Slave Use the IDE Primary Master/

WAFER-LX Motherboard Page 84 translation modes. Most systems now use hard drives with large capacities and therefore either the LBA translation mode

WAFER-LX Motherboard Page 85 Î Sector The Sector specification indicates how many logical sectors the HDD has been divided into. 6.3 Advanced BIOS

WAFER-LX Motherboard Page 86 Î Virus Warning [Disabled] NOTE: Many disk diagnostic programs can cause the above warning message to appear when the

WAFER-LX Motherboard Page 87 Î Enabled The system can be booted from a remote system through the LAN. Î SATA Boot ROM Control [Disabled] Use the

WAFER-LX Motherboard Page 88  USB-HDD  LAN  Disabled Î Boot Other Device [Enabled] Use the Boot Other Device option to determine whether the sys

WAFER-LX Motherboard Page 89 Î Gate A20 Option [Fast] Use the Gate A20 Option option to set if the keyboard controller or the chipset controls the

WAFER-LX Motherboard Page 90 Î Typematic Delay (Msec) [250] The Typematic Rate option can only be configured if the Typematic Rate Setting is enab

WAFER-LX Motherboard Page 91 Î HDD S.M.A.R.T [Disabled] Use the S.M.A.R.T option to enable S.M.A.R.T (Self-Monitoring, Analysis, and Reporting Tech

WAFER-LX Motherboard Page xi List of Figures Figure 1-1: WAFER-LX Overview ...

WAFER-LX Motherboard Page 92 Î Agent after boot [Disabled] Use the Agent after boot option to keep the console redirection agent active after the c

WAFER-LX Motherboard Page 93 6.4 Advanced Chipset Features Use the Advanced Chipset Features menu (BIOS Menu 4) to change chipset configuration opti

WAFER-LX Motherboard Page 94 Î Memory Frequency [333 MHz] Use the Memory Frequency option to set the frequency of the installed DRAM modules. The M

WAFER-LX Motherboard Page 95 Î OnBoard Audio [Enabled] Use the OnBoard Audio option to enable or disable the onboard codec. Î Disabled The onboard

WAFER-LX Motherboard Page 96 Î Disabled DEFAULT Memory is not reserved for ISA expansion cards Î Enabled Memory is reserved for ISA expansion cards

WAFER-LX Motherboard Page 97  1024 x 768  1152 x 864  1280 x 1024  1600 x 1200 Î Data Bus Type [9 – 24 bits, 1 ppc] The Data Bus Type optio

WAFER-LX Motherboard Page 98 Î VSYNC Polarity Active [Low] The VGSYNC Polarity Active option can only be configured if the Flat Panel Type option i

WAFER-LX Motherboard Page 99 6.5 Integrated Peripherals Use the Integrated Peripherals menu (BIOS Menu 6) to change the configuration options for th

WAFER-LX Motherboard Page 100  Master Drive PIO Mode  Slave Drive PIO Mode Î Auto DEFAULT The computer selects the correct mode. Î Mode 0 PIO

WAFER-LX Motherboard Page 101 Î IDE HDD Block Mode [Enabled] If the drive connected to the system supports block mode, use the IDE HDD Block Mode o

WAFER-LX Motherboard Page xii Figure 4-26: J7 Connector ...

WAFER-LX Motherboard Page 102  Disabled  3F8/IRQ4  2F8/IRQ3 (Default)  3E8/IRQ4  2E8/IRQ3  Auto Î Onboard Serial Port 3 [Disabled] Use the

WAFER-LX Motherboard Page 103 Î SPP DEFAULT The parallel port operates in the standard parallel port (SPP) mode. This parallel port mode works with

WAFER-LX Motherboard Page 104 6.5.1 IT8888 ISA Decode IO NOTE: Five PCI-104 devices can be stacked onto the WAFER-LX motherboard. If these devices

WAFER-LX Motherboard Page 105 The IT8888 ISA Decode IO menu has the following common options:  Decode I/O Space N  Decode I/O Speed N  Decode

WAFER-LX Motherboard Page 106 Î Decode IO Size N [Fast Speed] Use the Decode IO Size N option to specify the size of the ISA bus. The following opt

WAFER-LX Motherboard Page 107 BIOS Menu 8: IT8888 ISA Decode Memory The IT8888 ISA Decode IO menu has the following common options:  Decode Memory

WAFER-LX Motherboard Page 108 Î Enabled DEFAULT The Nth memory set is enabled and dedicated system memory resources are allocated to the ISA bus. Î

WAFER-LX Motherboard Page 109 6.6 Power Management Setup Use the Power Management Setup menu (BIOS Menu 1) to set the BIOS power management and savi

WAFER-LX Motherboard Page 110  Disabled Default  1 Min  2 Min  3 Min  4 Min  5 Min  6 Min  7 Min  8 Min  9 Min  10 Min  11 Min  12 Min

WAFER-LX Motherboard Page 111 Î Enabled The system alarm will turn the system on when the alarm goes off. If this option is enabled the following v

WAFER-LX Motherboard Page xiii Figure 8-5: System...

WAFER-LX Motherboard Page 112 Î No DEFAULT If the operating system does not meet the Plug and Play specifications, BIOS configures all the devices i

WAFER-LX Motherboard Page 113 BIOS Menu 11: IRQ Resources The IRQ Resources menu has the following options:  IRQ-3 assigned to  IRQ-4 assigned t

WAFER-LX Motherboard Page 114 Î x DMA Resources [Press Enter] The DMA Resources option (BIOS Menu 12) can only be selected if the Resources Control

WAFER-LX Motherboard Page 115 Î Legacy ISA Only an ISA card compliant with the original AT bus specification can be installed Î x Memory Resource

WAFER-LX Motherboard Page 116  N/A (Default)  C800  CC00  D000  D400  D800  DC00 Î x Reserved Memory Length [8K] The Reserved Memory Length

WAFER-LX Motherboard Page 117 6.8 PC Health Status The PC Health Status menu (BIOS Menu 14) has no user configurable options, but shows system oper

WAFER-LX Motherboard Page 118 Î Voltages The following voltages are monitored:  Vcore  +3.3 V  VccMem  +5 V  +12 V  VBAT(V)

WAFER-LX Motherboard Page 119 Chapter 7 7 RAID Setup

WAFER-LX Motherboard Page 120 7.1 VIA® RAID Utility The WAFER-LX has a VIA® VT6421 SATA controller chip onboard. The SATA RAID controller allows the

WAFER-LX Motherboard Page 121 7.3 Creating a RAID Array The steps for creating a RAID 0, RAID 1 and JBOD array are similar. To create a RAID array,

WAFER-LX Motherboard Page xiv Figure 8-40: Installation Complete...

WAFER-LX Motherboard Page 122 Step 3: Select the RAID type from the list that appears. Press Enter to select. Figure 7-4: RAID Type Step 4: Proce

WAFER-LX Motherboard Page 123 Step 2: All data on the hard disks is destroyed when the RAID array is setup. Press Y to setup the array, or N to go

WAFER-LX Motherboard Page 124 7.3.2 Manual Setup Step 1: Select “Select Disk Drives” and press Enter Figure 7-8: Select Drives Step 2: Select the

WAFER-LX Motherboard Page 125 Step 3: The “Source” or “Stripe0” drive is shown in green text with a [*] at the beginning. Step 4: Select the drive

WAFER-LX Motherboard Page 126 Step 6: Select the “Stripe Size” option and press Enter. Figure 7-12: Stripe Size Step 7: Select the stripe size fr

WAFER-LX Motherboard Page 127 Step 8: Select “Start Create Process” and press Enter to create the RAID array. Figure 7-14: Start RAID Creation Ste

WAFER-LX Motherboard Page 128 Step 10: The display message confirms that the array has been created. Details of the newly created array are shown in

WAFER-LX Motherboard Page 129 Step 2: Select the array to delete. Figure 7-18: Select Array to Delete Step 3: Press Y to delete the array, or N t

WAFER-LX Motherboard Page 130 Step 4: The display message confirms that the array has been deleted. Step 0: Figure 7-20: Array Deleted 7.5 Select

WAFER-LX Motherboard Page 131 Step 2: Select the array to set as a boot array. Figure 7-22: Select Boot Array Step 3: Press Enter to set the arra

WAFER-LX Motherboard Page xv List of Tables Table 1-1: WAFER-LX Model Specifications...

WAFER-LX Motherboard Page 132 Step 1: Select the “Serial Number View” option and press Enter. Figure 7-24: Serial Number View Step 2: Select the

WAFER-LX Motherboard Page 133 7.7 Exiting The RAID Utility To exit the RAID utility, press ESC. Press Y to exit or N to go back. Figure 7-26: Exit

WAFER-LX Motherboard Page 134 Chapter 8 8 Software Drivers

WAFER-LX Motherboard Page 135 8.1 Available Software Drivers NOTE: The content of the CD may vary throughout the life cycle of the product and is s

WAFER-LX Motherboard Page 136 Step 1: From the AMD LX/GX Driver CD main menu (Figure 8-1), click WAFER-LX. Figure 8-1: AMD LX/GX CD Main Menu Step

WAFER-LX Motherboard Page 137 Step 3: Select any item from the list to view more information on the driver installation, or select Manual to naviga

WAFER-LX Motherboard Page 138 Step 2: Double-click the “System” icon. Figure 8-4: Control Panel

WAFER-LX Motherboard Page 139 Step 3: Click the “Hardware” tab. Click DEVICE MANAGER. Figure 8-5: System Step 4: The “Device Manager” window open

WAFER-LX Motherboard Page 140 8.3 VGA Driver To install the VGA driver please follow the steps below. Step 1: Open the “Device Manager” (Section 8.

WAFER-LX Motherboard Page 141 Step 3: The Hardware Update Wizard appears. Click the “No, not this time” option. Click NEXT to continue. Figure 8-7

WAFER-LX Motherboard Page xvi Table 4-26: CN19 Connector Pinouts ...

WAFER-LX Motherboard Page 142 Step 4: Click the “Install from a list or specific location”. Click NEXT to continue. Figure 8-8: Installation Locat

WAFER-LX Motherboard Page 143 Step 5: Click “Don’t search. I will choose the driver to install”. Click NEXT to continue. Figure 8-9: Driver Locati

WAFER-LX Motherboard Page 144 Step 6: Click HAVE DISK to choose the driver from a specific location. Figure 8-10: Have Disk Step 7: Click BROWSE

WAFER-LX Motherboard Page 145 Step 8: Browse to the directory with the graphics driver. Figure 8-12: Graphics Driver Directory Step 9: Click on t

WAFER-LX Motherboard Page 146 Step 10: Click OK to continue. Figure 8-14: Install From Disk Step 11: Click on the driver that appears. Click NEXT t

WAFER-LX Motherboard Page 147 Step 12: The Windows logo testing warning window appears. Click CONTINUE ANYWAY to continue. Figure 8-16: Windows Log

WAFER-LX Motherboard Page 148 8.4 Audio Driver To install the audio driver please follow the steps below. Step 1: Open the “Device Manager” (Sectio

WAFER-LX Motherboard Page 149 Step 3: The Hardware Update Wizard appears. Click the “No, not this time” option. Click NEXT to continue. Figure 8-1

WAFER-LX Motherboard Page 150 Step 4: Click the “Install from a list or specific location”. Click NEXT to continue. Figure 8-20: Installation Loca

WAFER-LX Motherboard Page 151 Step 5: Click “Don’t search. I will choose the driver to install”. Click NEXT to continue. Figure 8-21: Driver Locat

WAFER-LX Motherboard Page xvii BIOS Menus BIOS Menu 1: Award BIOS CMOS Setup Utility ...

WAFER-LX Motherboard Page 152 Step 6: Click the “Sound, video and gamer controllers” option. Click NEXT to continue Figure 8-22: Have Disk Step 7:

WAFER-LX Motherboard Page 153 Step 8: Click BROWSE to choose the driver location. Figure 8-24: Browse For Driver Location Step 9: Browse to the d

WAFER-LX Motherboard Page 154 Step 10: Click on the driver file. Click OPEN to use this file and continue. Figure 8-26: Select Driver File Step 11:

WAFER-LX Motherboard Page 155 Step 12: Click on the driver that appears. Click NEXT to continue. Figure 8-28: Select The Driver Step 13: The Window

WAFER-LX Motherboard Page 156 Step 14: Click FINISH to exit the hardware installation wizard. Step 0: Figure 8-30: Installation Complete

WAFER-LX Motherboard Page 157 8.5 LAN Driver To install the LAN driver, please follow the steps below. Step 1: Open the “Device Manager” (Section 8

WAFER-LX Motherboard Page 158 Step 3: The Hardware Update Wizard appears. Click the “No, not this time” option. Click NEXT to continue. Figure 8-3

WAFER-LX Motherboard Page 159 Step 4: Click the “Install from a list or specific location”. Click NEXT to continue. Figure 8-33: Installation Loca

WAFER-LX Motherboard Page 160 Step 6: Click BROWSE to choose the driver location. Figure 8-35: Browse For Driver Location Step 7: Browse to the d

WAFER-LX Motherboard Page 161 Step 8: Click on the driver file. Click OPEN to use this file and continue. Figure 8-37: Select Driver File Step 9:

WAFER-LX Motherboard Page 162 Step 10: Click on the driver that appears. Click NEXT to continue. Figure 8-39: Select The Driver Step 11: Click FINI

WAFER-LX Motherboard Page 163 8.6 SATA/RAID Driver To install the VIA® SATA/RAID driver, please follow the steps below. Step 1: Click SATA from the

WAFER-LX Motherboard Page 164 Step 3: The Install Shield Wizard (Figure 8-42) is prepared to guide the user through the rest of the process. Figur

WAFER-LX Motherboard Page 165 Step 5: The VIA® Software License Agreement appears. Choose “I Agree” and click NEXT to continue. Figure 8-44: Softw

WAFER-LX Motherboard Page 166 Step 7: Review the items to be installed and click NEXT to begin the installation process (Figure 8-46). Figure 8-46

WAFER-LX Motherboard Page 167 Step 9: Once the installation is complete, the Install Wizard Complete screen appears (Figure 8-48). Save any work or

WAFER-LX Motherboard Page 168 8.7 ISA Driver To install the IT8888 ISA Bridge driver please follow the steps below: Step 10: Open the “Device Manage

WAFER-LX Motherboard Page 169 Step 12: The Hardware Update Wizard appears. Click the “No, not this time” option. Click NEXT to continue. Figure 8-5

WAFER-LX Motherboard Page 170 Step 13: Click the “Install from a list or specific location”. Click NEXT to continue. Figure 8-51: Installation Loca

WAFER-LX Motherboard Page 171 Step 14: Click “Don’t search. I will choose the driver to install”. Click NEXT to continue. Figure 8-52: Driver Locat

WAFER-LX Motherboard Page 1 Chapter 1 1 Introduction

WAFER-LX Motherboard Page 172 Step 15: Click HAVE DISK to choose the driver from a specific location. Figure 8-53: Have Disk Step 16: Click BROWSE

WAFER-LX Motherboard Page 173 Step 17: Browse to the directory with the graphics driver. Figure 8-55: Graphics Driver Directory Step 18: Click on t

WAFER-LX Motherboard Page 174 Step 19: Click OK to continue. Figure 8-57: Install From Disk Step 20: Click on the driver that appears. Click NEXT t

WAFER-LX Motherboard Page 175 Step 21: Click FINISH to exit the hardware installation wizard. Step 0: Figure 8-59: Installation Complete

WAFER-LX Motherboard Page 176 Appendix A A BIOS Options

WAFER-LX Motherboard Page 177 Below is a list of BIOS configuration options in the BIOS chapter. Î Load Fail-Safe Defaults ...

WAFER-LX Motherboard Page 178 Î Typematic Delay (Msec) [250]...

WAFER-LX Motherboard Page 179 Î Onboard Parallel Port [378/IRQ7]...

WAFER-LX Motherboard Page 180 Appendix B B Terminology

WAFER-LX Motherboard Page 181 AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and

WAFER-LX Motherboard Page ii Revision Date Version Changes 24 February, 2009 1.22 Corrected fan voltage label 16 December, 2008 1.21 Corrected p

WAFER-LX Motherboard Page 2 1.1 Overview The 3.5” WAFER-LX AMD LX-800 low power single board computer (SBC) is fully equipped with advanced multi-mo

WAFER-LX Motherboard Page 182 DMA Direct Memory Access (DMA) enables some peripheral devices to bypass the system processor and communicate directly

WAFER-LX Motherboard Page 183 LCD Liquid crystal display (LCD) is a flat, low-power display device that consists of two polarizing plates with a liq

WAFER-LX Motherboard Page 184 Appendix C C Digital I/O Interface

WAFER-LX Motherboard Page 185 C.1 Introduction The DIO connector on the WAFER-LX is interfaced to GPIO ports on the Super I/O chipset. The DIO has b

WAFER-LX Motherboard Page 186 C.3 Assembly Language Samples C.3.1 Enable the DIO Input Function The BIOS interrupt call INT 15H controls the digital

WAFER-LX Motherboard Page 187 Appendix D D Watchdog Timer

WAFER-LX Motherboard Page 188 NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for sp

WAFER-LX Motherboard Page 189 NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROG

WAFER-LX Motherboard Page 190 Appendix E E Address Mapping

WAFER-LX Motherboard Page 191 E.1 IO Address Map I/O address Range Description 000-01F DMA Controller 020-021 Interrupt Controller 040-043 System t

WAFER-LX Motherboard Page 3 1.1.2 Applications The WAFER-LX is designed for applications in the following areas:  Kiosks and Point of Sales  Rest

WAFER-LX Motherboard Page 192 E.2 1st MB Memory Address Map Memory address Description 00000-9FFFF System memory A0000-BFFFF VGA buffer F0000-FFFFF

WAFER-LX Motherboard Page 193 E.4 DMA Channel Assignments Channel Function 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Available 4 C

WAFER-LX Motherboard Page 194 Appendix F F Compatibility

WAFER-LX Motherboard Page 195 NOTE: The compatible items described here have been tested by the IEI R&D team and found to be compatible with th

WAFER-LX Motherboard Page 196 F.3 Compatible Memory Modules NOTE: The memory modules listed below have been tested on the WAFER-LX other memory mod

WAFER-LX Motherboard Page 197 Appendix G G Hazardous Materials Disclosure

WAFER-LX Motherboard Page 198 G.1 Hazardous Materials Disclosure Table for IPB Products Certified as RoHS Compliant Under 2002/95/EC Without Mercury

WAFER-LX Motherboard Page 199 Toxic or Hazardous Substances and Elements Part Name Lead (Pb) Mercury (Hg) Cadmium(Cd) Hexavalent Chromium(CR(VI)) Po

WAFER-LX Motherboard Page 200 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的

WAFER-LX Motherboard Page 201 Appendix H H RAID Levels

WAFER-LX Motherboard Page 4 1.1.5 Connectors Figure 1-1: WAFER-LX Overview

WAFER-LX Motherboard Page 202 RAID allows multiple disks to be connected in an array. A RAID array allows extra capabilities like increased speed an

WAFER-LX Motherboard Page 203 H.1 RAID 0 RAID 0, or striping, spreads data evenly over the disks in the RAID array. One block of data is written to

WAFER-LX Motherboard Page 204 H.2 RAID 1 RAID 1, or mirroring, places the exact same data on all disks in the RAID array. One block of data is writt

WAFER-LX Motherboard Page 205 H.3 JBOD JBOD, sometimes called concatenation, strings physical hard disks together to create one larger logical disk.

WAFER-LX Motherboard Page 206 Index

WAFER-LX Motherboard Page 207 5 5.25” form factor ...3 A anti-static precautions...24

WAFER-LX Motherboard Page 208 IDE flat cable ... iv, 65 IDE Interface connectors ...5

WAFER-LX Motherboard Page 209 USB connectors...75 Utility CD... iv

WAFER-LX Motherboard Page 5 Figure 1-2: WAFER-LX Solder Side Overview The WAFER-LX has the following connectors on-board:  1 x AT power connector

WAFER-LX Motherboard Page 6  1 x Reset button connector  1 x RS-232/422/485 serial port connector  2 x SATA connectors  1 x Suspend power in

WAFER-LX Motherboard Page 7 Specification WAFER-LX SSD CompactFlash® Super I/O W83627EHG Audio AC'97 Codec Realtek ALC203 LAN 10/100 Base-T du

WAFER-LX Motherboard Page 8 1.2 Operating System Packages 1.2.1 Windows XPE SP2 (350 MB image size stored in a 512 MB CF card) 1. Advance Set Top B

WAFER-LX Motherboard Page 9 Chapter 2 2 Detailed Specifications

WAFER-LX Motherboard Page 10 2.1 Overview This chapter describes the specifications and on-board features of the WAFER-LX in detail. 2.2 Dimensions

WAFER-LX Motherboard Page 11 2.2.2 External Interface Panel Dimensions External interface panel dimensions are shown in Figure 2-2. Figure 2-2: Exte

WAFER-LX Motherboard Page iii Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to impr

WAFER-LX Motherboard Page 12 2.3 Data Flow Figure 2-3 shows the data flow between the two on-board chipsets and other components installed on the mo

WAFER-LX Motherboard Page 13 2.4 AMD Geode™ LX 800 CPU The WAFER-LX series motherboards all come with a preinstalled AMD Geode™ LX 800 500 MHz CPU.

WAFER-LX Motherboard Page 14  Wakeup on SMI/INTR 2.5 System Chipset The WAFER-LX series motherboards all have a preinstalled AMD Geode™ CS5536 s

WAFER-LX Motherboard Page 15 2.6 Graphics Support The Geode LX processor’s Graphics Processor is a BitBLT/vector engine that supports pattern genera

WAFER-LX Motherboard Page 16 Feature AMD Geode™ LX Processor Color Pattern 8, 16, 32 bpp Transparent Pattern Monochrome Solid Fill Yes Pattern F

WAFER-LX Motherboard Page 17 2.9 Ethernet Controller Specifications 2.9.1 Overview The Realtek RTL8100C(L) is a highly integrated and cost-effective

WAFER-LX Motherboard Page 18  2.5/3.3 V power supply with 5 V tolerant I/Os 2.10 Drive Interfaces The WAFER-LX can support the following drive i

WAFER-LX Motherboard Page 19 2.11 Serial Ports The WAFER-LX has two high-speed UART serial ports, configured as COM1 and COM2. The serial ports have

WAFER-LX Motherboard Page 20 2.16 Operating Temperature and Temperature Control The maximum and minimum operating temperatures for the WAFER-LX are

WAFER-LX Motherboard Page 21  Two software selectable MIC inputs  +6/12/20/30dB boost preamplifier for MIC input  Stereo output with 6-bit

WAFER-LX Motherboard Page iv Packing List NOTE: If any of the components listed in the checklist below are missing, please do not proceed with the

WAFER-LX Motherboard Page 22 Voltage Current +5 V 1.53 A Table 2-2: Power Consumption 2.19 Packaged Contents and Optional Accessory Items 2.19.1

WAFER-LX Motherboard Page 23 Chapter 3 3 Unpacking

WAFER-LX Motherboard Page 24 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the WAFER-LX may resul

WAFER-LX Motherboard Page 25 3.3 Unpacking Checklist NOTE: If some of the components listed in the checklist below are missing, please do not proce

WAFER-LX Motherboard Page 26 Quantity Item and Part Number Image 1 SATA power cable (P/N: 32100-088600-RS) 1 RS-232/422/485 cable (P/N: 32200-026

WAFER-LX Motherboard Page 27 Chapter 4 4 Connectors and Jumpers

WAFER-LX Motherboard Page 28 4.1 Peripheral Interface Connectors Section 4.1.2 shows peripheral interface connector locations. Section 4.1.2 lists a

WAFER-LX Motherboard Page 29 Figure 4-2: Connector and Jumper Locations (Solder Side) 4.1.2 Peripheral Interface Connectors Table 4-1 shows a list

WAFER-LX Motherboard Page 30 Connector Type Label IDE Interface connector 44-pin header CN30 Inverter power connector 5-pin header CN3 Keyboar

WAFER-LX Motherboard Page 31 4.1.4 On-board Jumpers NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists o

WAFER-LX Motherboard Page v Table of Contents 1 INTRODUCTION...

WAFER-LX Motherboard Page 32 4.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible

WAFER-LX Motherboard Page 33 PIN NO. DESCRIPTION 3 GND 4 +5 V Table 4-4: AT Power Connector Pinouts 4.2.2 ATX Power Connector CN Label: CN2 CN Typ

WAFER-LX Motherboard Page 34 PIN NO. DESCRIPTION 3 PS_ON Table 4-5: ATX Power Connector Pinouts 4.2.3 ATX Power Button Connector CN Label: CN13 CN

WAFER-LX Motherboard Page 35 CN Type: 10-pin header (2x5) CN Location: See Figure 4-6 CN Pinouts: See Table 4-7 The audio connector is connected to

WAFER-LX Motherboard Page 36 4.2.5 Battery Connector CN Label: CN7 CN Type: 2-pin header (1x2) CN Location: See Figure 4-7 CN Pinouts: See Table 4-

WAFER-LX Motherboard Page 37 4.2.6 Compact Flash Connector CN Label: CN32 (solder side) CN Type: 50-pin header (2x25) CN Location: See Figure 4-8 C

WAFER-LX Motherboard Page 38 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 11 N/C 36 VCC_COM 12 N/C 37 IRQ15 13 VCC_COM 38 VCC_COM 14 N/C 39 CSEL 15

WAFER-LX Motherboard Page 39 Figure 4-9: Fan Connector Location PIN NO. DESCRIPTION 1 CPUFAN_OUT 2 +12 V 3 GND Table 4-10: Fan Connector Pinouts

WAFER-LX Motherboard Page 40 Figure 4-10: FDD Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 +5 V 14 STEP# 2 INDEX# 15 GND 3 +5

WAFER-LX Motherboard Page 41 4.2.9 GPIO Connector CN Label: CN14 CN Type: 10-pin header (2x5) CN Location: See Figure 4-11 CN Pinouts: See Table 4-

WAFER-LX Motherboard Page vi 2.10.3 Floppy Disk Drive (FDD)... 18 2.10.4

WAFER-LX Motherboard Page 42 4.2.10 IDE Connector CN Label: CN30 CN Type: 44pin header (2x22) CN Location: See Figure 4-12 CN Pinouts: See Table 4-

WAFER-LX Motherboard Page 43 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 21 IDE DRQ 22 GROUND 23 IOW# 24 GROUND 25 IOR# 26 GROUND 27 IDE CHRDY 28

WAFER-LX Motherboard Page 44 Figure 4-13: Inverter Connector Locations PIN NO. DESCRIPTION 1 ADJ (Def: GND) 2 GND 3 12 V 4 GND 5 BL_EN Table 4-1

WAFER-LX Motherboard Page 45 Figure 4-14: Keyboard/Mouse Connector Location PIN NO. DESCRIPTION 1 +5 V 2 MS DATA 3 MS CLK 4 KB DATA 5 KB CLK 6 GN

WAFER-LX Motherboard Page 46 Figure 4-15: LED Connector Locations PIN NO. DESCRIPTION 1 +5 V 2 GND 3 Power LED+ 4 Power LED- 5 HDD LED+ 6 HDD LED

WAFER-LX Motherboard Page 47 Figure 4-16:Print Port Connector Location PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 STB# 2 AFD# 3 PD0 4 ERR# 5

WAFER-LX Motherboard Page 48 CN Location: See Figure 4-17 CN Pinouts: See Table 4-18 The PC/104 power input connector provides power to the PC/104 e

WAFER-LX Motherboard Page 49 CN Pinouts: See Table 4-19 The PC/104 slot enables a PC/104 compatible expansion module to be connected to the board.

WAFER-LX Motherboard Page 50 Pin No. Column A Column B Column C Column D 14 SA17 IOR- SD10 DREQ6 15 SA16 DACK3- SD11 DACK7- 16 SA15 DREQ3 SD

WAFER-LX Motherboard Page 51 Figure 4-19: Reset Button Connector Locations PIN NO. DESCRIPTION 1 Reset+ 2 Ground Table 4-20: Reset Button Connect

WAFER-LX Motherboard Page vii 4.2.8 Floppy Disk Connector (Slim Type, Optional)... 39 4.2.9 GPIO Conne

WAFER-LX Motherboard Page 52 Figure 4-20: RS-232 Serial Port Connector Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 DCD# 2 DSR# 3 RXD 4

WAFER-LX Motherboard Page 53 Figure 4-21: SATA Drive Connector Locations PIN NO. DESCRIPTION 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND Table 4-22

WAFER-LX Motherboard Page 54 The TFT LCD LVDS can be connected to a TFT LCD screen directly. Figure 4-22: TFT LCD LVDS Connector Pinout Locations

WAFER-LX Motherboard Page 55 4.2.21 TFT LCD TTL Connector CN Label: CN28 CN Type: 40-pin header (2x20) CN Location: See Figure 4-23 CN Pinouts: See

WAFER-LX Motherboard Page 56 PIN NO. DESCRIPTION PIN NO. DESCRIPTION 25 R0 26 R1 26 R2 28 R3 29 R4 30 R5 31 R6 32 R7 33 GND 34 GND 35 CLK 36

WAFER-LX Motherboard Page 57 Figure 4-24: USB Connector Pinout Locations PIN NO. DESCRIPTION PIN NO. DESCRIPTION 1 VCC_USB 2 GND 3 DATA3- 4 DA

WAFER-LX Motherboard Page 58 Figure 4-25: WAFER-LX On-board External Interface Connectors 4.3.2 USB Combo Port CN Label: CN19 CN Type: USB Combo p

WAFER-LX Motherboard Page 59 PIN DESCRIPTION PIN DESCRIPTION 1 TX+ 2 TX- 3 RX+ 4 NC 5 NC 6 RX- 7 NC 8 NC Table 4-27: J7 Connector Pinouts F

WAFER-LX Motherboard Page 60 PIN DESCRIPTION PIN DESCRIPTION 3 TXD1 4 DTR1 5 GND 6 DSR1 7 RTS1 8 CTS1 9 COM_RI1 Table 4-29: COM1 Pinouts Fi

WAFER-LX Motherboard Page 61 PIN DESCRIPTION PIN DESCRIPTION PIN DESCRIPTION 5 GROUND 10 GROUND 15 DDCCLK Table 4-30: VGA1 Connector Pinouts F

WAFER-LX Motherboard Page viii 5.5 JUMPER SETTINGS ...

WAFER-LX Motherboard Page 62 Chapter 5 5 Installation and Configuration

WAFER-LX Motherboard Page 63 5.1 Anti-static Precautions Electrostatic discharge (ESD) can cause serious damage to electronic components, including

WAFER-LX Motherboard Page 64 o When installing or configuring the motherboard, place it on an antistatic pad. This helps to prevent potential ESD d

WAFER-LX Motherboard Page 65 Do not place a PCB on top of an anti-static bag. Only the inside of the bag is safe from static discharge. 5.3.2 Chec

WAFER-LX Motherboard Page 66 WARNING! Please note that the installation instructions described in this manual should be carefully followed in order

WAFER-LX Motherboard Page 67  The SO-DIMM socket supports SDRAM DIMM speeds of 333 MHz and 400 MHz 5.4.1.2 DIMM Module Installation The WAFER-LX m

WAFER-LX Motherboard Page 68 Quantity Type 2 SATA cables 1 SATA power cable 1 RS-232 cable 1 USB cable Table 5-1: IEI Provided Cables 5.4.2.1 IDE

WAFER-LX Motherboard Page 69 5.5 Jumper Settings NOTE: A jumper is a metal bridge that is used to close an electrical circuit. It consists of t

WAFER-LX Motherboard Page 70 Figure 5-2: Jumper Locations 5.5.1 AT Power Select Jumper Settings Jumper Label: JP1 Jumper Type: 2-pin header Jumper

WAFER-LX Motherboard Page 71 5.5.2 COM3 Setup Jumper Settings Jumper Label: JP2 Jumper Type: 3-pin header Jumper Settings: See Table 5-4 Jumper Loc

WAFER-LX Motherboard Page ix 7.1 VIA® RAID UTILITY ... 120

WAFER-LX Motherboard Page 72 COM2 Setup Description 2-4 12 V 4-6 or 6-8 5 V 8-10 RI Default Table 5-6: COM2 Pin 9 Setup 5.5.4 LCD Voltage J

WAFER-LX Motherboard Page 73 CompactFlash® Setup Description 2-3 IDE Master Table 5-8: CompactFlash® Master/Slave Setup 5.5.6 TFT LCD Type Jumpe

WAFER-LX Motherboard Page 74 keep it disconnected for at least five seconds. After five seconds has elapsed, reinsert the connector. If the “CMOS Se

WAFER-LX Motherboard Page 75 5.7.3 USB Connection The rear panel USB connectors provide easier and quicker access to external USB devices. The rear

WAFER-LX Motherboard Page 76 Chapter 6 6 BIOS Setup

WAFER-LX Motherboard Page 77 6.1 Introduction A licensed copy of Phoenix Award BIOS is preprogrammed into the ROM BIOS. The BIOS setup program allow

WAFER-LX Motherboard Page 78 Key Function F5 Previous values for the page menu items F6 Fail-safe defaults for the current page menu items F7 Op

WAFER-LX Motherboard Page 79 6.1.5 Main BIOS Menu Once the BIOS opens, the main menu (BIOS Menu 1) appears. BIOS Menu 1: Award BIOS CMOS Setup Util

WAFER-LX Motherboard Page 80  PC Health Status: Monitors essential system parameters. The following user configurable options are also available i

WAFER-LX Motherboard Page 81 Î Exit Without Saving Use the Exit Without Saving option to exit the BIOS menus without saving any configuration chan